19" Racking

Magnetic Fan Dust Filter Cover. (Sold in Pairs). Held in place with 4 Neodymium Magnets and can easily be removed for cleaning.Designed to fit over...

Smoked Plexiglass Barn Doors for Credenza Wood RacksFor use with Beech and Knotty Oak finish racks. Not compatible with Nebraska Oak and Tiepolo Wa...

Flat pack / knock-down 450mm Deep Beech Wood laminate rack kits with M6 threaded rack rails.Made from high quality 18mm laminate boards.Perfect for...

250mm Deep Beech Wood laminate rack sleeves with M6 threaded rack rails.Made from high quality 18mm laminate boards.Perfect for use in studios, off...

1U Vertical Cable Retaining Clip (Sold as a Pair) Part No. CM01R Material Steel Finish Black Description Cable Retaining Clip

Rack cable manager, 1U Panel with 5 Plastic Rings for Cable Management. Part No. CMP-1U Material Steel/Plastic Finish Black ...

1U Cable Management Slotted Duct with Cover. A neat solution to cross patch wiring looms. Part No. CMP-SD Material Steel/Plastic ...

This is a very quiet 1U Hot Air Extraction Unit, which uses 3 miniature blowers to expel heat from any 19” equipment racks.Behind the 1U Escutcheon...

Accessories for rack cooling systems:CRC-LINK 2.1mm to 2.1mm DC link cable for use with the 2000mA PSU or connect FT-DTC Digital Thermostatic Contr...

Accessories for rack cooling systems:CRC-TEMP Plug-in thermostat enables the fan to activate only when it reaches a certain temperature. This incre...

2U Rack Mountable Digital Thermostatically Controlled Quiet Fan Exhaust unit, for use in 19” equipment racks.It has been designed be fitted in-betw...

Replacement  Barrel Lock & Key For RCXX600 Series Contractor Flat Pack Rack System Doors.

Lockable Vented Laptop Drawers. Internal dimensions listed in the table.  Part No. EX-6101B Material 1.2mm Steel Finish Black Internal Dime...

19" Rack Mountable 1U Vented Laptop/Tablet Drawer with Foam Wrist-Pad for support and rear cable access.Key lockable. Part No. EX-6301B Mater...

19" Rack Mountable 1U Vented Laptop/Tablet Drawer with Foam Wrist-Pad for support and rear cable access.Key lockable. Part No. EX-6301B Mater...

Set of 4 Steel Adjuster Feet with M8 thread for Rack Enclosures.Use with R8230 Open Tower Rack System, R2020 Modular Rack Tower, R8200 Open Rack To...

Low noise 3U Heat Extraction Units are designed to be fitted into the front or back of a 19-inch rack to suck hot air out of an enclosure. As hot a...

This 1U Rack Mountable Digital Thermostatic Controller can be used to monitor and control all of our low noise DC fan units: CoolRaC, FT01-Q, FT02-...

Quiet and versatile Rack Fan Unit. Easy switch from a 1U fan tray to a 6U blower.Can either draw in or expel air from the front or the back of the ...

Dual Fan Kit for Wall Mount RacksFT02-Q quiet fan kits are designed to be fitted in pre-punched WM and WMP wall mounted racks. A 1A universal PSU i...

Tinted PlexiGlass Full Width Doors with key lock for Credenza Wood Racks.For use with Beech and Knotty Oak finish racks. Not compatible with Nebras...

M6 Flat Black Plastic Washer Part No. HSM6FW Material Plastic Finish Black Description M6 Plastic Washer

Self-Adhesive Ali/Plastic ID Strip. Part No. ID-STRIP Material Aluminium/Plastic Length 435mm Description Self Adhesive P...

19 Racking LCD mount has the following features:Mounts 12 to 22 Inch MonitorsVESA Mounting Interface StandardVariable Depth Settings Part No...